Support

FAQ

Search:
Find: or and Go  
77 entries found.

What do I need to take into account when directly selecting setpoint values with MI4 units ?

  • Information on this can be obtained by clicking the question.

How do you enter Configuration mode on MI4 units if the ENTER key has been assigned a macro ?

  • By means of special operations during the power-up

How can I connect up an MI4 or MV4 unit via Sucosoft S30 ?

  • Use the S30-AM-I40 application modu

What settings are required to connect an MI4 to a PS4-341 via Suconet K ?

  • a) Check MI4 configuration
    b) Check PLC Topology Configurator

As take is the MV4 coupling to a Mitsubushi A series PLC ?

  • With the communications module AJ71C24

What is with the communication between a MV4 and a Siemens PLC, to heed ?

  • Attention: The Bytes are reversed.

Is it possible to set the panel brightness of the MI4-471-TC1 touch panel ?

  • Unfortunately not with this type !

Is it possible to expand the memory of a MI4-471-TC1 Touch Panel
with a 2 or 4 MByte memory ZB4-902-SF1 or ZB4904-SF1?

  • Yes

Why is the MV4-Configurator only available with the type MV4-CFG-1 ?

  • MV4-CFG-1-GB

Which available MV4-devices are not listed in Main Catalogue ?

  • Typen: MV4-590-TA1 und /TA2 und /-XX1

Which touch panels are available in stainless steel?

  • MV4 Touch panels.

Is it possible to implement an MV4 interface via Device Net ?

  • Yes, with MV4 configurator MV4-CFG-1 since version 3.12.4 and a communication card ZB4-606-IF1.

What should be done if the write protection in the MV4 standard recipe management function cannot be removed ?

  • Only possible with MV4 configurator MV4-CFG-1 from version 3.12.

How can a message be printed out on MI4 display and operator systems?

  • Information on this is provided in an application note that can be obtained free-of-charge from the Internet.

How can an MI4 operator panel be connected to a Siemens S7 PLC?

  • An MI4 operator panel can be connected to a Siemens S7 PLC via MPI.

How can an MV4 touch panel be connected to a Siemens S7 PLC?

  • An MV4 touch panel can be connected to a Siemens S7 PLC using PROFIBUS-DP.

What are the chemical substances that the front of the MV4 touch operator panel is resistant to?

  • Click the question to obtain information on the chemical resistance of the MV4 front panel.

Is it possible to synchronize the time between several MI4 display and operator units?

  • Yes! This is described in an application note that is available from the Internet.

Is there any presentation material for the MI4-display and operating units ?

  • Yes

Is the software for configuring MI4 display and control devices compatible to Windows 2000 and Windows NT?

  • Yes, from version 2.01

What is the meaning of the flashing DEF-Dirty LED on the MV4 ?

  • When this LED is flashing, either the IR frame is slightly dirty or an IR sensor has failed. The flashing LED is only a warning.

What should be remembered on the MV4 Touch Operator Panel in order to prioritize the ″Print Report″ function while the ″Print Online Errors″ function is active ?

  • Click the question to obtain further information.

Which MI4 Operator Panels are approved by the Underwriters Laboratories (UL) and for the Canadian market (C UL) ?

  • You see table:

Is there a DEMO version for the MV4 Configurator (Galileo) ?

  • Yes, with clicks the question you reach the download.

What are the functional changes in the MV4-CFG-1-D/GB version V4.00.1 ?

  • See answer!

Can masks used on MV4-xxx and MI4-xxx touch panels burn the display if they are displayed continuously over a long period ?

  • Yes

How can data be transferred from a PS4 to another PLC system and displayed on an MV4 ?

  • Yes it is possible. Please click the question to obtain further information.

Can an MI4-140-KF1 (MI4 hand-held) be connected to an
Siemens S7-300 / S7-400 via MPI ?

  • Yes, MPI connections are supported.

How can Moeller PLCs be connected to SCADA or visualisation systems of other manufacturers ?

  • SCADA/visualisation systems with an OPC-Interface can be linked directly to a Moeller PLC using the S40-OPC server. Data transfer is implemented via RS232, modem or Ethernet TCP/IP.

Is it possible to display only the alarm text in an MI4 - project and suppress the red Alarm LED in the event of a fault ?

  • When creating the MI4 project in the MI4-CFG-1 software activate the following option:
    Project => Alarms => Message only

What is the minimum quantity available for customized seals for the MI4 devices ?

  • Please click on the question to obtain further information !

Which devices are available as a replacement of the MV4-590-TA1 and
MV4-590-TA2 ?

  • Please click on the question to obtain further information !

Which Touch Panel design software version (Galileo) is required for configuring the MV4-690-TBx device ?

  • Please click on the question to obtain further information !

Is the documentation for the MV4 Configuration Software AWB-C2700-1348D (Galileo, Galileo Runtime) also available in printed form?

  • Yes, but only in German Language. Order number: 255881

Some MI4 units have keys are labelled with letters. How can these keys be accessed in the Keyboard Macro Editor?

  • Please click on the question to obtain further information !

How is the integrated alphabetical keyboard used on some MI4 devices?

  • Please click on the question to obtain further information !

What information is required for determining the layout costs for customized seals (logos) for MI4 or MV4 devices ?

  • Please click on the question to obtain further information !

Is it possible to write a macro in the MI4 Keyboard Macro Editor that is only run if two or more keys are pressed simultaneously ?

  • Please click on the question to obtain further information !

Can different macros be assigned to the same key for MI4 ?

  • Please click on the question to obtain further information !

What is the final date of availability of Touch Panel VTP1- and VTP2 devices including accessories ?

  • The final date of availability of Touch Panel VTP1- and VTP2 devices including accessories is the december 2002.

Which MI4 operator and display units are no longer available?

  • Please click on the question to obtain further information!

Can event scripts for the MV4... (Galileo Software V 4.0) be started automatically or triggered by a bit?

  • Please click on the question to obtain further information!