FAQ

Search:
Find: or and Go  
102 entries found.

How do you enter Configuration mode on MI4 units if the ENTER key has been assigned a macro ?

  • By means of special operations during the power-up

How do you exchange data via Profibus DP between a Moeller PLC with a CM4-504/LE4-504/PS416-NET-441 and a Siemens S7/C7?

  • Use Siemens system function SFC13/SFC14/SFC15.

How can you display I/O status information and other modules in the DP Configurator, and how do you force the outputs?

  • Click on the question to obtain information.

How can you connect a PROFIBUS-DP master and a PROFIBUS-DP slave to the PS4-341-MM1 together?

  • Click on the question to obtain information.

How can I connect up an MI4 or MV4 unit via Sucosoft S30 ?

  • Use the S30-AM-I40 application modu

Does Sucosoft S40 include the FAlarm function block?

  • The EdgeAlarm function block is available instead.

Can Sucosoft S40 also be run on Linux?

  • Information on this can be obtained by clicking the question

On which PC operating systems does the PROFIBUS-FMS Configurator run ?

  • From version 3.3 or higher, MS-Windows 95, MS-Windows 98 and MS-Windows NT. Before this version, only MS-Windows 3.xx.

Is the NG31 still available or is there a similar substitute ?

  • A substitute can be obtained directly from the company Hubert Schröter. Click the question to obtain information.

How can you map a larger number of I/O to the marker range ?

  • Use the

Is there a German version of the Profibus DP Configurator ?

  • Click on the question to obtain information.

Which version of Sucosoft S40 supports: Structured text programming (ST) ?

  • From Sucosoft S40; version 5.0

How do you transfer the PLC time to the MV4 ?

  • Click on the question to obtain information.

How is the environment language selected in the MV4 Configurator ?

  • In the menue: Config

How can consistent data be received with a Profibus DP master?

  • By adjustment of the consistent data length

Can Sucosoft S40; version 4.00 still run on Windows 3.11 ?

  • No, since S40 uses 32-bit functions.
    The S40 runs with Windows 95/98 or with Windows NT 4.0

Can the S40 OPC Server V1.0 for Windows NT copied to
hard disk drive E too with 1.26 GB free memory ?

  • Yes, please further information heeds. (Clicks the question)

Is it possible to set the panel brightness of the MI4-471-TC1 touch panel ?

  • Unfortunately not with this type !

How can closed-loop control tasks be implemented with the PS4/PS416 PLC systems ?

  • There are two application modules with two-point controllers, three-point controllers, PID controllers and there is a closed-loop control toolbox for complex closed-loop control.

Is there an OPC interface for Moeller PS4/PS416 programmable controllers ?

  • The S40 OPC-server interface is available for the PS4/PS416 programmable controllers.

How can the PS4/PS416 system receive and evaluate the DCF77 radio time signal ?

  • A DCF77 receiver is required for receiving the DCF77 radio time signals and a software is required for evaluating the signal.

What is an application module?

  • An application module contains software function blocks for the PLC. These software modules offer solutions for standard automation tasks.

How many characters can be entered in the comment field in the POU Editor under POU Info ?

  • The comment field of the POU is 15 KByte.

Is it possible to carry out remote diagnostics for the PS4/PS416 system ?

  • Remote diagnostics can be carried out using a modem connection between the programming device and the PLC.

Is it possible to run a Suconet K2 line with the PS416 ?

  • The PS416-NET-210 Suconet K1/K2 card and the S40-AM-K2-D/GB application module are required for running Suconet K2 with the PS416.

How can I send and receive SMS messages with the PS4/PS416 system?

  • SMS application modules (software function blocks) allow SMS messages (SMS = Short Message Service) to be sent and received.

Do the PS4 compact PLCs have a MODBUS/JBUS interface ?

  • A MODBUS/JBUS interface can be implemented using the S40-AM-K4-D/GB application module and an interface converter.

How can large volumes of data be transferred via Suconet K or PROFIBUS-DP ?

  • The Suconet K/PROFIBUS-DP data multiplexer application module enables the transfer of large data volumes.

Is it possible to carry out floating point arithmetic operations with PS4 compact PLCs ?

  • Floating point arithmetic is a basic function of the PS4-341-MM1. With the PS4-150/200 you can use the S40-AM-A1-D/GB application module to implement floating point arithmetic functions.

Can the Sucom_A functionblock be used on the PS4-... MM1 in order to program the PLC with Sucosoft S40 ?

  • No

Is there a data multiplexer for Suconet-K / PROFIBUS-DP ?

  • Yes, the application module S40-AM-K1-GB contents a data multiplexer for Suconet-K / PROFIBUS-DP.

Where can I get the latest Sucosoft S40 Service Pack?

  • From the MOELLER FTP Server, please click on the question.

How is the current version of the Profibus-DP Configurator for S40 available ?

  • Over download, please click on the question.

Why is the MV4-Configurator only available with the type MV4-CFG-1 ?

  • MV4-CFG-1-GB

Is there a software to support the PROFIBUS-DP link of the Easy control relay to the EASY204-DP module with a MOELLER control system PS4 / PS416 ?

  • The S40-AM-K6-D/GB application module is provided for this purpose. Click the question to obtain the application module via the Internet.

Is the software for configuring MI4 display and control devices compatible to Windows 2000 and Windows NT?

  • Yes, from version 2.01

Which MI4-units and frequency inverters are supported from Sucosoft S40, Version V4.21 ?

  • Click the question to obtain further information.

What is the name of the application module for data exchange between the EASY204-DP and PS4-341/PS416 ?

  • The application module is called S40-AM-K6-D/GB.

How can the analog values of the potentiometers on PS4 controllers be converted to TIME type variables?

  • Click the question to obtain further information.

What are the function changes of version 2.04 of MI4-CFG-1-D/GB ?

  • Click the question to obtain further information.

How can I reach the version 2.04 of the MI4-Generier-Software MI4-CFG-1 ?

  • A Download is possible with clicks the question.

Where are the version lists for Moeller PS4/PS416, EM4, LE4, Sucosoft and MI4/MV4 ?

  • With clicks the question you reach the current version lists.

What is the application module for Ethernet data coupling with the
PS4-150/-200/-341 and PS416 ?

  • Yes, the application module S40-AM-K5-GB. With clicks the question to download.

What must be done when the Sucosoft S40 V4.xx will not start in conjunction with network printers running under WIN2000 ?

  • Click the question to obtain further informations.

Which termination resistance values are required with PROFIBUIS-DP ?

  • 390 Ohms / 220 Ohms / 390 Ohms

Can the PROFIBUS-DP Configurator CFG-DP (version V2.0) be downloaded ?

  • Please click the question !

Where can the S40-AM-... application modules be downloaded ?

  • When clicks the question a download is possible.

What is the name of the Excel file for outside temperature measurement in Bonn, incl. time and date?

  • an27k15d.exe

Which S40 software version can be run on which Windows version ?

  • Please click on the question to obtain further information.

Can MV4 (Galileo) versions 3.x and 4.x be installed in parallel in separate directories?

  • Yes, but both programs must not be started at the same time since it is not possible to copy the data from a 3.x project to a 4.x project.

How can data be transferred from a PS4 to another PLC system and displayed on an MV4 ?

  • Yes it is possible. Please click the question to obtain further information.

Can a PS4 or PS416 program be SAVED/RESTORED (packed/unpacked) ?

  • Yes, with the function: SAVE in the S40 navigator.

What are the new features of Sucosoft S40 Version V5.0 ?

  • The Sucosoft S40 version V5.0 is a 32-bit software that can be run on Windows operating systems 98 (SE), ME, NT 4.0 (SP6), 2000 (SP2), XP and XP Pro. Automatic variable declaration and Structured Text are new functions.

Does the S40-AM-TD; Version V2.0 application module contain any new functions for dial-up lines compared to version V1.x ?

  • Please click on the question to obtain further information.

What new functions for leased-line communication does the S40-AM-TL Version V2.1 application module provide compared to Version V1.x ?

  • Expansion to 64 outstations, the parameters are assigned using the function block.

Does WINbloc and XI/ON have the same function in the same network type ?

  • Yes, this is ensured without restriction.

With which standards and regulations for industrial requirements does WINbloc comply ?

  • Standards and regulations:
    VDE 0611 Part 1/8.92
    IEC/EN 60 947-7-1

Is it possible to display only the alarm text in an MI4 - project and suppress the red Alarm LED in the event of a fault ?

  • When creating the MI4 project in the MI4-CFG-1 software activate the following option:
    Project => Alarms => Message only